牧草收穫搬運車

PRIMO

The smooth operator: years ahead on experience Offset feeding tines with a cam track control system at each end saves power during loading. Pickup, chopping and loading in quick succession - no peak loads on any of the knives. Due to the optimum cam control system, the forage is picked up tidily and cut effortlessly at two banks of knives. The virtually circular cam track controls the feeding tines to guarantee jolt-free loading even when the wagon is full - good for the wagon, forage and driver. Due to the pickup bearings being located nearer the centre there is less bending stress acting on the shaft than on single-piece systems. Stress on each cam control track is 50 % lower than systems with a single cam track. Feeding tine shaft has hardened and polished end stubs for a longer service life. LADEPROFI and ERNTEPROFI have six feeding tine bars, and SILOPROFI have eight feeding tine bars for an extremely rapid loading sequence. These wagons are known for their smooth operation and above average capacity. The crop is handled carefully and cut precisely, without power peaks. Wide angle c.v. joint p.t.o shaft with cam-type clutch as standard The clutch disengages automatically if it is overloaded. The clutch engages again automatically after the p.t.o. shaft speed has been lowered. No grating - transmission components cannot be overloaded. ... the best knife security on any self-loading wagon Knives of hardened tool steel, serrated on one side, guarantee a long service life. Their perfect serrated blade ensures that even after the edge has dulled a good cut is still achieved. The curved knife shape delivers a continuous, power-saving cut. The forage is always cut with precision, it is not dragged through, torn apart or squashed. The knives are just hooked into the holders so they can easily be removed individually. This makes maintenance easier. The knife security Patented knife security - technology that has been proven over a thousand times. Each individual knife is protected. Triggering pressure remains the same, regardless of where the foreign object makes contact. The knife moves away with hardly any resistance after the triggering pressure has been reached. This protects both the knife and its edge. The knife mounting absorbs the impact from the foreign object, during which the knife acts against a spring to move slightly in the direction of rotation of the rotor. If the knife moves far enough the trigger roll presses it out of its holder. The knife can then move back almost without any resistance at all. The knife moves away with hardly any resistance after the triggering pressure has been reached. This protects both the knife and its edge. Small stones either fall away through the transfer plates, or can pass through the cutting system no problem. With larger stones the knives deflect back. This type of security system is not only extremely reliable, it also ensures that the knives remain sharp. Two knife banks with practical knife preselection system: Top knife bank: 4 forage quick-release knives (rough chop), 12-knife bank (16 knives) Lower knife bank Silage chopping system: 15 knives Knife combinations: 4/12/15/16/19/27/31

PROFIMATIC! Cutting system crank can also be used to rotate the loading system. The feeding tines can be rotated manually. Makes lubrication and maintenance much easier. Bolted pickup shaft bearings with replaceable bushes. Easy to remove, individually replaceable, extremely wear resistant. Central lubrication manifold The pickup bearings are lubricated from a central point as standard. Knife bank pivoting Straightforward hand crank on LADEPROFIs and ERNTEPROFIs. Hydraulic system optional. Pöttinger knife grinding bench for self-loading wagon knives. Solid, stable table with electric motor. Grinding disc mounted on parallelogram arms. All joints fitted with sealed bushes. Precision blade sharpening in seconds: sharp knives cut better and consume less tractor power.

Hydraulic coupling For hydraulic pickup lift system, or hydraulic scraper floor. The hydraulic coupling can be combined with a hand pump so no hydraulic connection is necessary. Convenient and straightforward operation.(for PONY, BOSS junior 1 and 2) Cab control unit with preselected programs Hydraulic cab control unit for Pick-up scraper floor tailgate Comfort version: Hydraulic drawbar Extension SELECT CONTROL One-finger operation All hydraulic functions controlled electronically - no more hydraulic hoses in the cab. Only one single-acting hydraulic connection with return line required. Pick-up, drawbar, scraper floor, tailgate, extension, chopping system are all operated hydraulically. Optional for BOSS junior 2 (with hydraulic scraper floor), BOSS Junior 3, BOSS and PROFI GP, standard for ERNTEBOSS 2 H.   Every ERNTEPROFI features electronic controls The front end control box for the loading functions is always in the cab. Control unit for: pickup drawbar roof extension scraper floor tailgate The two control panels can be joined to form a neat unit.

METERING! ERNTEBOSS The metering system at the rear end of the wagon is convenient to operate. The speed of the scraper floor can be regulated to exactly match the throughput of a forage blower. ERNTEPROFI The control box for operating the unloading functions can be mounted either next to the front control box, or at the tailgate.

PONY, BOSS, PROFI-GP Choice of axles Braked axles, high-loaders fitted with reversible rims (changes track width from 1550 mm to 1750 mm). Bolted axle unit enables tandem axle with suspension to be retrofitted. Tandem axle with compensating suspension A compound suspension system (optional) optimises the load distribution to each axle. Tyres: 15-17, reversible for track width of 1550 and 1750 mm 19.0/45-17, track width 1600 mm LADE-/ERNTEPROFI With 15-17 tyres the track width can easily be changed from 1550 to 1750 mm by turning the wheels around. On trailers with tandem axles offsetting the track widths of 1550 and 1750 mm will help to distribute the load more evenly. Single axle up to 6.9 t permissible total weight, 25 km/h. Dual air brakes for single axle up to 5.6 t permissible total weight, 40 km/h 19.0/45-17/10 PR. Tandem axle up to 8 t permissible total weight, 25 km/h, Dual air brakes with ALB for tandem axle up to 9 t permissible weight, 40 km/h 15.0/55-17/10 PR Air brakes or hydraulic brakes (varies from country to country) Pneumatic brake system with ALB controller (automatic load-controlled brake system) can be upgraded to ABS as option High degree of safety with higher loads even with the hydraulic braking system. Each wheel is fitted with a brake cylinder as standard Steered axles as option Steered axles to protect the sward and reduce side forces while cornering. The steered axles are locked by a separate hydraulic connection for reversing and higher speeds. Protects the tyres against wear.

NEAT! Spring suspension tandem axles The compound suspension optimises the load distribution to each axle. While driving over bumpy ground the forces are distributed to both axles, not adsorbed by the limit stops. Best control on slopes, same load on each axle, even during braking. Huge leaf springs provide the necessary shock absorption

　

PRIMO 350 The PRIMO 350 is a trailer with single axle and 1536 cuft / 35 m3 capacity. With the new, hydraulically foldable dry grass assembly this is a classic trailer for daily feeding in low buildings.

PRIMO 350 with high dry matter grass assembly

The new high dry matter grass assembly for the PRIMO 350 L, 400 L and 450 L.
This allows the hydraulic folding of the trailer top to a total height of 8.53 ft / 2.6 m. Smooth unloading into low buildings is then possible when used in conjunction
with the pendular backboard.

The name of the new silage trailer, the PRIMO, with its controlled conveyor arms, was taken from the Latin “primo”, which roughly means “the best”. The farmer can select from 236, 1413, 2285 or 2825 ft3 / 40, 45, 50 or 63 m31 . The PRIMO 400 and 450 series can also be supplied with beater rotors, the PRIMO 630 with its 6 knives is a typical hay trailer.

The PROFIMATIC loading system is the at the heart of the PRIMO. Six powerful, overlapping conveyor combs with central lubrication provide a twelve phase cutting sequence (8 combs on request). The conveyor arms are controlled by a cam track control system on both sides 1.
The knife bank on the PRIMO has 31 knives in two rows. With a theoretical cutting length of 1.69” / 43 mm, this machine comes close to the cutting quality of the FARO.
Automatic chain lubrication with 8 conveyor combs.

The PRIMO contains the same platform as the FARO and the EUROPROFI:
The bolted frame construction  1 is
6’11”/ 2.1 m  wide. The end-to-end C-profile made of high-strength fine grain steel, with straight, heavy duty stays, ensures the necessary stability.

PRIMO and FARO are equipped with tandem axles (9 springs per wheel) as standard. Compensating rockers 1 ensure optimum weight distribution. Tyres 19/45-17, on request 500/50-17 und 555/45-17


PICK-UP
The pickup has a width of 1.80 m / 5.91’. Five tine tubes 2 guarantee a high degree of stability. These are supported by a central metal support disc 3. The non-twisting pick up is relieved of the load on both sides with springs 4 and is self-aligning. The pickup is controlled using one cam track made of steel with a solid centre. The control rollers made from two-row, permanently lubricated bearing rollers, are sturdy and designed for large quantities of forage.
Tempered-steel plates 5 keep dirt and small foreign bodies out of the cutting unit.

　

Technical data PRIMO 350 L 400 L 450 L 500 L 630 L Volume [m³]: 35  40  45  50  63  Volume according to DIN 11741 [m³]: 22  25,5  28,5  31,5  38,5  D with discharger rotors / L without rotors: L  L  L  L  L  Pick-up width [mm]: 1800  1800  1800  1800  1800  Pick-up width DIN [mm]: 1740  1740  1740  1740  1740  Number of knives: 31 (16+15)  31 (16+15)  31 (16+15)  31 (16+15)  6  Maximum knife spacing [mm]: 43  43  43  43  210  Platform height [mm]: 1140  1190  1190  1190  1250  Loading area [mm]: 5000x2100  5680x2100  6360x2100  6360x2100  7730x2100  Length [mm]: 8090  8760  9450  9150  10500  Width [mm]: 2420  2420  2420  2420  2420  Height [mm]: 3450  3500  3500  3700  3760  Height - holded down [mm]: 2550  2600  2600  2630  2630  Approx. weight [kg]: 3660  3910  4160  4560  4950  Dimensions and weights are subject to change due to ongoing technical development, and vary from country to country.

Standard Equipment Short-chop self loading wagon with 31- knife cutting system Power requirement: 6 feeding-tine bar version from 51KW/70HP to 81KW/110HP 8 feeding-tine bar version from 51KW/70HP to 96KW/130HP Standard equipment: Axles: Tandem axles 4 wheel brake; 11,5 t max total weight, track width 1800 mm Tyres: 19/45-17 14 ply FLOTATION+, 6 hole rim, ET-35 Hitch: universal high hitch drawbar, height adjustable with spindle, rigid towing eye, max. drawbar weight 1500 kg P.T.O. shaft: wide angle P.T.O. shaft with cut-out clutch, 540 rpm, max. torque 1200 Nm Pick-up: 1.80m wide with 5 rows of tines pneumatic pick-up wheels (15 x 6,0 - 6) Loading system: PROFIMATIC loading aggregate with 6 off-set feeder combs, in the middle section to 2/3 overlapped, cam track control at each end, central lubrication manifold, optional 8 feeder combs c/w automatic drive chain lubrication Cutting system: loading and cutting system with automatic knife security system, optional 1 bank c/w max. 6 knives or 1 upper bank c/w 16 knives and/or 1 lower bank c/w 15 knives Bodywork: metal sections, galvanised and plastic coated, roof section can be folded inwards D-model: 2-parted hydraulic universal tailgate - fine discharging possible, side access door with fold away ladder Scraper floor: hydraulic scraper floor drive, 2 chains (Primo 500 with 4 chains) and infinitely adjustable speed, forward and reverse-control, automatic floor control D-Version: Rear discharge system, 2 large diameter, removable beaters, engaged/disengaged by shifting claw ahead of angular gear unit Tailgate: L-version: large opening angle D-version: universal tailgate for fine discharging Plugs: 1 SA valve with open return Control: L-version: Direct Control D-version: Power Control

瑋洲企業有限公司

台灣高雄市前鎮區武德街135巷24號

TEL : 886-7-7169249  Fax : 886-7-7169250

e-mail : agri-machine@weizhou.com.tw

e-Mail : shiu@ksts.seed.net.tw

http://www.weizhou.com.tw/Agrimachine/i-foragewagon/index.htm

Skype : service450429

MSN : steveLee73@hotmail.com

回本網站首業                 回農機首業